Instalé Debian 9 stretch (escritorio GNOME) de 64 bits en mi PC. Mi adaptador inalámbrico USB (TP-LINK TL-WN722N) fue detectado automáticamente después de instalar el firmware de atheros:
apt-get install firmware-atheros
Pero no puedo conectarme a ningún marco inalámbrico, ya sea que estén protegidos con contraseña o sin protección.
Conecté mi USB. Se detectó, se envió la autenticación, se autenticó, pero se canceló la autenticación de inmediato. Deshabilitar IPV6 no resolvió mi problema..
Aquí está mi dmesg informe:
[ 59.880805] usb 1-1.4: new high-speed USB device number 4 using ehci-pci
[ 60.005727] usb 1-1.4: New USB device found, idVendor=0cf3, idProduct=9271
[ 60.005729] usb 1-1.4: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[ 60.005731] usb 1-1.4: Product: USB2.0 WLAN
[ 60.005732] usb 1-1.4: Manufacturer: ATHEROS
[ 60.005734] usb 1-1.4: SerialNumber: 12345
[ 60.324981] usb 1-1.4: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
[ 60.325069] usbcore: registered new interface driver ath9k_htc
[ 60.348095] usb 1-1.4: firmware: direct-loading firmware ath9k_htc/htc_9271-1.4.0.fw
[ 60.629962] usb 1-1.4: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
[ 60.880826] ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
[ 61.111895] ath9k_htc 1-1.4:1.0: ath9k_htc: FW Version: 1.4
[ 61.111897] ath9k_htc 1-1.4:1.0: FW RMW support: On
[ 61.111899] ath: EEPROM regdomain: 0x809c
[ 61.111900] ath: EEPROM indicates we should expect a country code
[ 61.111901] ath: doing EEPROM country->regdmn map search
[ 61.111911] ath: country maps to regdmn code: 0x52
[ 61.111912] ath: Country alpha2 being used: CN
[ 61.111912] ath: Regpair used: 0x52
[ 61.122477] ieee80211 phy0: Atheros AR9271 Rev:1
[ 61.185069] ath9k_htc 1-1.4:1.0 wlx18a6f7160a49: renamed from wlan0
[ 61.224640] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 61.361032] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 61.535923] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 61.743450] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 69.190250] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 70.360621] wlx18a6f7160a49: authenticate with 74:23:44:dc:0f:d7
[ 70.551637] wlx18a6f7160a49: send auth to 74:23:44:dc:0f:d7 (try 1/3)
[ 70.556012] wlx18a6f7160a49: authenticated
[ 75.555233] wlx18a6f7160a49: aborting authentication with 74:23:44:dc:0f:d7 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 76.872114] wlx18a6f7160a49: authenticate with 74:23:44:dc:0f:d7
[ 77.061146] wlx18a6f7160a49: send auth to 74:23:44:dc:0f:d7 (try 1/3)
[ 77.065158] wlx18a6f7160a49: authenticated
[ 82.061225] wlx18a6f7160a49: aborting authentication with 74:23:44:dc:0f:d7 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 83.775718] wlx18a6f7160a49: authenticate with 74:23:44:dc:0f:d7
[ 83.965040] wlx18a6f7160a49: send auth to 74:23:44:dc:0f:d7 (try 1/3)
[ 83.969807] wlx18a6f7160a49: authenticated
[ 88.969792] wlx18a6f7160a49: aborting authentication with 74:23:44:dc:0f:d7 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 91.207178] wlx18a6f7160a49: authenticate with 74:23:44:dc:0f:d7
[ 91.395860] wlx18a6f7160a49: send auth to 74:23:44:dc:0f:d7 (try 1/3)
[ 91.400263] wlx18a6f7160a49: authenticated
[ 93.996839] wlx18a6f7160a49: aborting authentication with 74:23:44:dc:0f:d7 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 94.061841] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
[ 94.233433] IPv6: ADDRCONF(NETDEV_UP): wlx18a6f7160a49: link is not ready
No tengo idea de por qué sucedió esto, ni por qué se abortó varias veces en un solo intento.
Relacionado:Ms-access:¿cómo conectar la base de datos de MS Access a la LAN?Editar:informe iwconfig:
enp3s0 no wireless extensions.
wlx18a6f7160a49 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
lo no wireless extensions.
Respuesta aceptada:
De alguna manera, mi firmware tuvo problemas con el nombre de interfaz largo. Así que ejecuté este comando para evitarlo:
ln -s /dev/null /etc/systemd/network/99-default.link
y funcionó.